Just how do you feel when it comes to How to Install a Bathtub Yourself?
Mounting a tub isn't exactly rocket science, however it does require solid plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bathtub with a new one is also a moderately hard task. If the old tub is readily obtainable, the job can move immediately; if you have to open up a wall surface to remove the old tub and position the brand-new tub, the task is much harder. In either instance, the task is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and embeded in the brand-new one. Make sure you have actually certified on your own for the task and also fit attempting it. Instead of hiring a specialist to take over a halfway-completed task, it is far better to take into consideration employing one prior to you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will assist you mount a new bathtub in your restroom if you have already acquired a brand-new tub and do not require to transform the arrangement of your previous water pipes.
Your tools and material list must comprise the following:
Planning for the Installation
First of all, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently be ready to be suited its final position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any water staying in the system. The process of getting rid of the existing taps can be fairly troublesome because of the restricted gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using the two wood boards under its feet, place the tub in the required position. The wooden boards are valuable in evenly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by examining the level and readjusting the feet on the tub up until the spirit level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet adapter to the suitable supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water system and inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bathtub as well as likewise inspect the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bathtub needs to wait until the bath tub has been used at the very least once as this will certainly resolve it right into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin guaranteeing that the washers are in location between the faucet and the sink. Protect the tap in position with the maker offered backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous type ought to be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to crack a rigid seal, triggering the water to permeate the wall surface in between the bath and also the tiling, bring about issues with dampness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your components and also fittings. They are offered in tubes and also cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of drenched paper or soft rope. Remember to constantly load the tub with water before securing, to permit the movement experienced when the tub is in use. The sealer can crack fairly early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our section on Tools You Need to Install a New Bathtub . Thanks a lot for finding the time to read our article post. Do you know about someone else who is serious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Please feel free to share it. We truly appreciate reading our article about Tools You Need to Install a New Bathtub .
Get professional leak detection today.